Notes —Lets you add notes about your drivers. Exit —Lets you exit the Manage Drivers dialog. Click the top of each column to sort accordingly. Click on the column head to sort the column. Create, copy, and edit drivers with Driver Wizard To enhance device support in Composer Pro and in the Control4 system, a device needs a corresponding driver, known as a device driver. Go menu Access the Go menu from the menu bar on any Composer Pro screen. The following options are available: System Design —Lets you build the project tree and identify the devices in the Control4 system.
Media —Lets you add and scan stored or broadcast media. Agents —Lets you set up agents for use on the system and programming. Programming —Lets you program devices and agents on the system. Tools menu Access the Tools menu from the menu bar on any Composer Pro screen. The following options are available: System Manager —Launches a tool to connect to and configure Control4 Controller hardware and devices.
See" Zigbee Health. The Network view shows you which devices in your project are identified and communicating to the network. Device Logs —Download a snapshot of device logs from controllers, touchscreens, or Triad One streaming amplifiers.
System Diagnostics —Assists you in gathering system information to help you determine if any issues encountered are configuration problems, performance issues, or potential defects. The System Diagnostics tool is valuable also for logging information and sending email to Control4 Technical Support.
It is also required in conjunction with a customer account to enable Remote Access, which allows secure access to your system via the Internet. Zigbee Network —Lists information about the Zigbee devices.
Z-Wave Network —Lists information about the Z-Wave devices The icons denote the following: Green —Indicates that an address is identified and the device is online. For example, a dimmer is identified and communicating to the Control4 system. Yellow —Indicates that an address is identified and the device is offline. For example, if the System Remote Control goes to sleep, the status turns yellow. This indicates that the System Remote Control has been identified, but it is offline.
Red —Indicates that a device is not identified or has been offline for a long period of time. The Network Tools tabs are shown below.
Zigbee Network tab This tab displays Zigbee devices, addresses, online states, and signal strengths You can view the Zigbee network items two ways using these radio buttons: Tree —Takes the devices that are in the project and lists them in a room tree view. List —Takes the devices that are in the project and lists them in one list. Tab descriptions: Connections —Lists all the connections in the project. Lets you search by keywords, and expand by room or the whole house. In the Connections tab, if you right-click on an item, more menu options are available.
Expand All —Expands all the items and rooms in the list. Collapse All —Collapses all the items and rooms in the list. Refresh —Refreshes the connections and rooms in the list.
Disconnect —Disconnects the selected connection. Programming —Shows programming that has been created. Can expand the events to include actions.
In the Programming tab, if you right-click on an item, more menu options are available. Collapse to Events —Collapses all the items and rooms in the list to only show events with programming defined. Remove —Removes the programming script items from the selected event.
Controller Performance t ab —Lets you view controller performance information, including CPU and memory usage. Process data is listed in the bottom pane. History b utton —Lets you view the history of CPU and memory performance. Test Internet Connection b utton— Lets you test the current Internet connection. After viewing, click Close to exit the dialog box.
System Info t ab— Lets you view system information in a tree view. Click Save To File to save this information. Logging t ab— Lets you log system problems. This logging feature lets you: Change the logging level of any of the program loggers on the operating system. Select from fatal , error , warning , info , debug , trace , and default.
To start the tail, select the log, then click Start Tail. To stop the tail, click Stop Tail. Open the current log file of the selected program logger.
To open the log, select the logger, then click Open Log. View all the logs available on the device at that location. Click Auto Scroll Output to scroll through the log entries, or click Clear Output to clear all entries.
Click Update. Click Begin Update. To update the system software: Click Update to update the system. After you begin the updates, you cannot modify your project. Do not remove any power cords or Ethernet cables until the updates are completed.
You can have an email message sent to you when the update completes to notify you when you can modify the project again. To view the project, you can close the Update Manager dialog without interrupting the update, but you cannot make any changes.
Click View Logs in the Update Manager dialog to view the update messages. Click Cancel Pending to cancel the device downloads. This action cancels a download from the device. Air purifier PM2. Smart Kettles can now be controlled! Outdoor IR Patio Heaters can now be controlled. Where can i buy Tuya enabled products? What brands utilise Tuya? The driver only supports wifi based Tuya products at the moment. Zigbee, IR and Bluetooth devices are not supported. V2 of the Tuya Driver offers many benefits over the original driver, including access to a wider range of functionality using variables, increased feedback performance with the option to subscribe to Tuya Cloud services to further increase the performance to realtime speeds and support using the official API which offers long term support.
V1 and V2 drivers are NOT intercompatible. Note This solution is cloud based and as such requires an active internet connection for operation. This solution is cloud based and as such requires an active internet connection for operation. Not all commands are exposed. To configure, refer to documentation or watch the QuickStart Video Tutorial. Please note, extensive testing of blinds is strongly recommended some blinds may not be supported.
It supports all boolean, Integer and enumeration variables and similar to our other drivers, exposes them as Control4 variables , and provides easy access to announcement triggers. It is strongly recommended that Device Status Notifications is enabled. We recommend upgrading endusers to this version and configuring the new functionality. Introducing our brand new Sensor Subdriver. It supports all boolean, Integer and enumeration variables and similar to our other drivers, exposes them as Control4 variables.
One click access to announcements is included. Trigger an announcement such as a doorbell when a PIR is triggered or a button is pressed As with all of our Tuya drivers, it can be mixed or matched with any driver or device as required We Strongly recommend enabling Status Notifications to use this driver introduced in Despite the appearance of a changing percentage in the tuya app, the server may not actually send the new level This can be avoided by exclusively using Control4 with Levels or only the Level functionality in the Tuya App.
Please test the level functionality extensively, to ensure it's suitable for your requirements. This allows huge new functionality, and some of the following benefits: Almost instant feedback on most devices even when activated by the device itself Wifi PIR sensors and more advanced wifi smart home products can now be utilised which rely on fast feedback Tuya devices like switches could be used to trigger Control4 commands Greatly reduced API calls may be required in many cases to reduce API calls, slow the polling rate.
Refer to the Release Notes associated with the software release for specific instructions. Optional To ensure the driver database is updated:. Tip: When Composer Pro is first installed, the My Drivers tab is pre-populated with a list of drivers. The My Drivers tab provides shortcuts to commonly-used drivers. You can add, remove, and re-order items to the My Drivers tab as needed. Removing drivers from My Drivers tab only removes the driver from the list. It still exists in the Local Database.
To get back to the default My Drivers tab list and to include newly-added Control4 devices, right-click any device and click Restore Default List.
0コメント